Ok I got my cocktail here, the board isnt in it , but I have a game board. The card edge connector isnt marked pin# 1 etc nor is it made to fit only one way. How do I know which way to coonnect it? Brian
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
Try to check with the game manual. Check where is the power inside the connector with dmm. Hope this help.
Unfortunately there was no manual....
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
JAMMA? ok i think i forgot to mention i'm new with the vids so treat me as stupid ok? The board is a Vigilante game , theres two boards together mounted piggyback . The cabinet has a connector that is oo small for the board so it looks as if somebody created a jumper to convert to the larger size that appars to fit many other boards. Ill try to post a pic..
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
Ignore the bottom part of this image, somewhere on your board you will see an edge connector like the one shown... It may or may not have a space on your PCB....anyway looking at it0 the far right is the "power section" just following the right side of your harness to the power supply... the other end will be going to the control panel...
Follow me? holding your harness look at each end one end will have wires going to your power supply that is the end that goes on the right side of that edge connector looking at ifrom the top (top is the side with chips and cap etc...
YES! Tglover is a crackhead! Complete MAACA-Wacko!
Posts
1,734
Gender
Male
Posts Per Day
0.84
Time Online
168 days 23 hours 52 minutes
Location
GTA, Ont.
Age
35
Sounds like you've got a pre-jamma cab that has some sort of conversion harness added, and your board is jamma.
Here's the standard JAMMA pinout. All you need to do it locate the end of the connector with the grounds and 5V lines on the end as that is the end that goes towards the notch on the PCB.
But before you plug the board in and flip the switch I'd bust out the DMM and test the voltages on the connector. You never know what was done with that conversion harness.
Cool thanks, It looks like a home made harness . Is there a harness available to buy , I will post a pic in a few minutes....
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
$10 bucks I can you a new one with your board easy peasy I would actually recomend that anyway... prolly need one for your board too in the cocktail.. just a thought
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
Sounds fine B1 can you get me the board and 2 connectors. I think my son might have toasted the Vigilante though, he went and plugged it in and turned the unit on. Please tell me it wont fry the board too easily......
Humans are like Slinkys, it always puts a smile on your face when you push one down the stairs!
My Pins.... Simpsons....Finally ! Elektra Bram Stokers Dracula..... Time 2000.../ Middle Earth for sale CHEAP! Totem...project Meteor....project Truck Stop... HAUNTED HOUSE woot...it works now, just needs a shop job!
Vids Steel Gunner II 60 in 1ocktail...
GONE.... EFTLW, Wipeout , Dungeons and Dragons, World Cup Soccer 78, Sinbad
the harness has a green wire at the RIGHT end (as pictured) I "suspect" the is a gorund and the power end I was talking about...
Now still looking at pic 1 the way it sits...the green end would got to the LEFT end of the edge connector on the board
So esentailly flip the harness and plug it in BUT
As menace said turn the machine on WITHOUT plugging the board in and check the harness voltages usng the pinout Doug linked I would start at the grren end and work in...